Honda CR-V: Automatic Transmission
Honda CR-V (2006–2011) Service Manual / Transaxle / Automatic Transmission
Special Tools
07HAE-PL50101 may also be used to substitute one of 07LAE-PX40100.
- Mainshaft Holder
- Attachment, 78 x 90 mm
- Clutch Spring Compressor Bolt Assembly
- Holder Handle
- Oil Seal Driver Attachment
- Attachment, 40 x 50 mm
- Clutch spring Compressor Attachment
- Bearing Installer Attachment
- Installer Shaft
- A/T Pressure Hose, 2,210 mm
- A/T Pressure Hose Adapter
- Attachment, 78 x 80 mm
- Attachment, 42 mm I.D.
- Companion Flange Holder
- Clutch Compressor Attachment
- Tapered Bearing Outer Race Attachment
- Preload Inspection Tool
- A/T Clutch Pressure Gauge Set/Panel
- Adjustable Bearing Puller, 25-40 mm
07736-A01000B or 07736-A01000A must be used with commercially available 3/8 "-16 slide hammer.
- Attachment, 32 x 35 mm
- Attachment, 42 x 47 mm
- Attachment, 52 x 55 mm
- Attachment, 62 x 68 mm
- Attachment, 72 x 75 mm
- Attachment, 22 x 24 mm
- Attachment, 40 x 42 mm
- Driver, 40 mm 1.0.
- Attachment, 35 mm 1.0.
- Driver
- Oil Seal Driver Attachment
- Oil Seal Driver Attachment
- General Troubleshooting Information
- System Description
- DTC Troubleshooting
- Road Test
- Pressure Test
- Shift Solenoid Valve
- A/T Clutch Pressure Control Solenoid Valve
- ATF Temperature Sensor
- ATF Level Check
- ATF Replacement
- Transfer Assembly Inspection/Removal/Installation
- Transmission Removal/Installation
- ATF Cooler
- Shift Lever
- Shift Cable
- A/T Gear Position Indicator
- A/T Interlock System
- Transmission End Cover
- Transmission Housing
- Valve Body
- Torque Converter Housing
- Shafts and Clutches
- A/T Differential
- Transfer Assembly Inspection/Disassembly/Reassembly
READ NEXT:
General Troubleshooting Information
How to Check for DTCs with the Honda
Diagnostic System (HDS)
When the powertrain control module (PCM) senses an
abnormality in the input or output system, the D
indicator (A) in the gauge control modu
General Operation
The automatic transmission is a combination of a 3-element torque converter
and triple-shaft electronically controlled
unit which provides 5 speeds forward and 1 reverse. The entire unit is
position
SEE MORE:
Side Engine Mount Bracket Replacement
1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
3. Remove the ground cable (A), then remove the side
engine mount bracket (B).
4. Install the side engine mount bracket, then loosely
tighten the new bolt and nut (C), and loosely tighten
the bolt
Relay and Control Unit
Locations
Engine Compartment
VSA MODULATOR-CONTROL UNIT
AUXILIARY UNDER-HOOD
RELAY BOX
POWER MIRROR
DEFOGGER RELAY
PCM
RADIATOR FAN RELAY
ELECTRONIC THROTTLE CONTROL SYSTEM (ETCS) CONTROL RELAY
ELD UNIT
PGM-FI MAIN RELAY 1 (FI MAIN)
UNDER-HOOD FUSE/RELAY BOX
FAN CONTROL RELAY
BLOWER MOTOR RELAY
© 2016-2025 Copyright www.hcrv.net
