Honda CR-V: Pressure Test

Special Tools Required

1. Make sure the transmission fluid is filled to the proper level.

2. 4WD model: Raise the vehicle on a lift, make sure it is securely supported, and allow all four wheels to rotate freely.

2WD model: Raise the front of the vehicle, make sure it is securely supported, and allow the front wheels to rotate freely. Or raise the vehicle.

3. Remove the splash shield.

4. Connect the oil pressure gauge to the line pressure inspection port (A). Do not allow dust or other foreign particles to enter the hole while connecting the gauge.

Honda CR-V. Automatic Transmission

5. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).

6. Turn off the engine, and connect the HDS to the DLCV(A).

NOTE: If the HDS does not communicate with the PCM, troubleshoot the DLC circuit.

Honda CR-V. Automatic Transmission

7. With the shift lever in the P or N position while holding the engine speed at 2,000 rpm, measure the line pressure.

NOTE: If the shift lever is in positions other than P or N, higher pressure may be shown.

Honda CR-V. Automatic Transmission

8. Turn the engine off, then disconnect the oil pressure gauge from the line pressure inspection port.

9. Install the sealing bolt to the line pressure inspection port with a new sealing washer, and tighten the bolt to 18 N*m (1.8 kgf*m, 13 lbf*ft). Do not reuse the old sealing washer.

10. Connect the oil pressure gauge to the 1st clutch pressure inspection port (B).

Honda CR-V. Automatic Transmission

11. Remove the air cleaner housing and intake air duct, and connect the oil pressure gauge to the 2nd clutch pressure inspection port (C). Then temporarily install the air cleaner housing and the intake air duct.

Honda CR-V. Automatic Transmission

12. Start the engine.

13. Shift to the 1 position, and measure the 1 st clutch pressure at the 1st clutch pressure inspection port (B) while holding the engine speed at 2,000 rpm.

14. Shift to the 2 position, and measure the 2nd clutch pressure at the 2nd clutch pressure inspection port (C) while holding the engine speed at 2,000 rpm.

Honda CR-V. Automatic Transmission

15. Turn the engine off, remove the air cleaner housing and intake air duct, then disconnect the oil pressure gauges from the 1st clutch pressure and 2nd clutch pressure inspection ports.

16. Install the sealing bolts in the 1st clutch pressure and 2nd clutch pressure inspection ports with new sealing washers, and tighten the bolts to 18 N*m (1.8 kgf*m, 13 Ibf*ft). Do not reuse the old sealing washers.

17. Install the air cleaner housing and intake air duct.

18. Connect the oil pressure gauge to the 3rd clutch pressure inspection port (D) and the 5th clutch pressure inspection port (F).

Honda CR-V. Automatic Transmission

19. Connect the oil pressure gauge to the 4th clutch pressure inspection port (E).

Honda CR-V. Automatic Transmission

20. Cancel the transmission 2nd-hold control mode with the HDS; choose Pressure Test Assistance Mode in the Miscellaneous Test Menu of the A/T Mode Menu.

21. Start the engine, shift to the D position, and select the D3 driving mode by pressing the D3 switch.

22. Measure the 3rd clutch pressure at the 3rd clutch pressure inspection port (D) while holding the engine speed at 2,000 rpm.

23. Release the D3 driving mode by pressing the D3 switch, and measure the 4th clutch pressure at the 4th clutch pressure inspection port (E) while holding the engine speed at 2,000 rpm.

24. Measure the 5th clutch pressure at the 5th clutch pressure inspection port (F) while holding the engine speed at 2,000 rpm.

Honda CR-V. Automatic Transmission

25. Bring the engine back to an idle, then apply the brake pedal to stop the wheels from rotating.

26. Shift to the R position, then release the brake pedal.

Raise the engine speed to 2,000 rpm, and measure the 4th clutch pressure at the 4th clutch pressure inspection port (E).

Honda CR-V. Automatic Transmission

27. Turn the engine off, then disconnect the oil pressure gauges from the 3rd, 4th, and 5th clutch pressure inspection ports.

28. Install the sealing bolts in the 3rd, 4th, and 5th clutch pressure inspection ports with new sealing washers, and tighten the bolts to 18 N*m (1.8 kgf*m, 13 Ibf*ft). Do not reuse the old sealing washers.

29. If the pressure measurements are out of the service limit, the possible problems and probable causes are listed in the table.

Honda CR-V. Automatic Transmission

30. Install the splash shield.

READ NEXT:

 Shift Solenoid Valve

Shift Solenoid Valve Test 1. Connect the HDS to the DLC (A). 2. Choose Shift Solenoid A, B, C, D, and E in the Miscellaneous Test Menu on the HDS. NOTE: If the HDS does not communicate with the PCM,

 A/T Clutch Pressure Control Solenoid Valve

A/T Clutch Pressure Control Solenoid Valve A Test 1. Connect the HDS to the DLC (A). 2. Choose Clutch Pressure Control (Linear) Solenoid A in the Miscellaneous Test Menu on the HDS. NOTE: If the HDS

 ATF Temperature Sensor

ATF Temperature Sensor Test/Replacement 1. Raise the vehicle on a lift, or apply the parking brake, block the rear wheels, and raise the front of the vehicle. Make sure it is securely supported. 2. R

SEE MORE:

 Engine Installation

Special Tools Required Universal eyelet 07 AAK-SNAA 120 Engine hanger adapter VSB02C000015 * Front subframe adapter VSB02C000016 * CR-V engine hanger adapter VSB02C000032 * Engine support hanger, A and Reds AAR-T-12566 * * : Available through American Honda Tool and Equipment Program, 1-888-

 System Description

Overview The audio unit acts as the "processor" for all audio functions. Select audio functions from the audio unit, the audio remote (on the steering wheel), or by using the navigation voice control system. The audio display provides the current audio status. For vehicles with navigation, additio

© 2016-2024 Copyright www.hcrv.net