Honda CR-V: Automatic Transmission
Honda CR-V (2006–2011) Service Manual / Transaxle / Automatic Transmission
Special Tools
07HAE-PL50101 may also be used to substitute one of 07LAE-PX40100.
- Mainshaft Holder
- Attachment, 78 x 90 mm
- Clutch Spring Compressor Bolt Assembly
- Holder Handle
- Oil Seal Driver Attachment
- Attachment, 40 x 50 mm
- Clutch spring Compressor Attachment
- Bearing Installer Attachment
- Installer Shaft
- A/T Pressure Hose, 2,210 mm
- A/T Pressure Hose Adapter
- Attachment, 78 x 80 mm
- Attachment, 42 mm I.D.
- Companion Flange Holder
- Clutch Compressor Attachment
- Tapered Bearing Outer Race Attachment
- Preload Inspection Tool
- A/T Clutch Pressure Gauge Set/Panel
- Adjustable Bearing Puller, 25-40 mm
07736-A01000B or 07736-A01000A must be used with commercially available 3/8 "-16 slide hammer.
- Attachment, 32 x 35 mm
- Attachment, 42 x 47 mm
- Attachment, 52 x 55 mm
- Attachment, 62 x 68 mm
- Attachment, 72 x 75 mm
- Attachment, 22 x 24 mm
- Attachment, 40 x 42 mm
- Driver, 40 mm 1.0.
- Attachment, 35 mm 1.0.
- Driver
- Oil Seal Driver Attachment
- Oil Seal Driver Attachment
- General Troubleshooting Information
- System Description
- DTC Troubleshooting
- Road Test
- Pressure Test
- Shift Solenoid Valve
- A/T Clutch Pressure Control Solenoid Valve
- ATF Temperature Sensor
- ATF Level Check
- ATF Replacement
- Transfer Assembly Inspection/Removal/Installation
- Transmission Removal/Installation
- ATF Cooler
- Shift Lever
- Shift Cable
- A/T Gear Position Indicator
- A/T Interlock System
- Transmission End Cover
- Transmission Housing
- Valve Body
- Torque Converter Housing
- Shafts and Clutches
- A/T Differential
- Transfer Assembly Inspection/Disassembly/Reassembly
READ NEXT:
General Troubleshooting Information
How to Check for DTCs with the Honda
Diagnostic System (HDS)
When the powertrain control module (PCM) senses an
abnormality in the input or output system, the D
indicator (A) in the gauge control modu
General Operation
The automatic transmission is a combination of a 3-element torque converter
and triple-shaft electronically controlled
unit which provides 5 speeds forward and 1 reverse. The entire unit is
position
SEE MORE:
DTC 21-1x ("x" can be 0 thru 9 or A thru F):
Open or Increased Resistance in Driver's Seat
Belt Tensioner
DTC 21-1x ("x" can be 0 thru 9 or A thru F):
Open or Increased Resistance in Driver's Seat
Belt Tensioner
Special Tools Required
SRS inflator simulator 07SAZ-TB4011A
SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Proce
Cam Chain Inspection
1. Remove the front wheels.
2. Remove the splash shield (see step 21).
3. Remove the drive belt.
4. Remove the cylinder head cover.
5. Set the No.1 piston at top dead center (TDC). The
punch mark on the variable valve timing control
(VTC) actuator and the punch mark on the exhaust
camshaft sproc
© 2016-2025 Copyright www.hcrv.net
