Honda CR-V: Automatic Transmission
Honda CR-V (2006–2011) Service Manual / Transaxle / Automatic Transmission
Special Tools
07HAE-PL50101 may also be used to substitute one of 07LAE-PX40100.
- Mainshaft Holder
- Attachment, 78 x 90 mm
- Clutch Spring Compressor Bolt Assembly
- Holder Handle
- Oil Seal Driver Attachment
- Attachment, 40 x 50 mm
- Clutch spring Compressor Attachment
- Bearing Installer Attachment
- Installer Shaft
- A/T Pressure Hose, 2,210 mm
- A/T Pressure Hose Adapter
- Attachment, 78 x 80 mm
- Attachment, 42 mm I.D.
- Companion Flange Holder
- Clutch Compressor Attachment
- Tapered Bearing Outer Race Attachment
- Preload Inspection Tool
- A/T Clutch Pressure Gauge Set/Panel
- Adjustable Bearing Puller, 25-40 mm
07736-A01000B or 07736-A01000A must be used with commercially available 3/8 "-16 slide hammer.
- Attachment, 32 x 35 mm
- Attachment, 42 x 47 mm
- Attachment, 52 x 55 mm
- Attachment, 62 x 68 mm
- Attachment, 72 x 75 mm
- Attachment, 22 x 24 mm
- Attachment, 40 x 42 mm
- Driver, 40 mm 1.0.
- Attachment, 35 mm 1.0.
- Driver
- Oil Seal Driver Attachment
- Oil Seal Driver Attachment
- General Troubleshooting Information
- System Description
- DTC Troubleshooting
- Road Test
- Pressure Test
- Shift Solenoid Valve
- A/T Clutch Pressure Control Solenoid Valve
- ATF Temperature Sensor
- ATF Level Check
- ATF Replacement
- Transfer Assembly Inspection/Removal/Installation
- Transmission Removal/Installation
- ATF Cooler
- Shift Lever
- Shift Cable
- A/T Gear Position Indicator
- A/T Interlock System
- Transmission End Cover
- Transmission Housing
- Valve Body
- Torque Converter Housing
- Shafts and Clutches
- A/T Differential
- Transfer Assembly Inspection/Disassembly/Reassembly
READ NEXT:
General Troubleshooting Information
How to Check for DTCs with the Honda
Diagnostic System (HDS)
When the powertrain control module (PCM) senses an
abnormality in the input or output system, the D
indicator (A) in the gauge control modu
General Operation
The automatic transmission is a combination of a 3-element torque converter
and triple-shaft electronically controlled
unit which provides 5 speeds forward and 1 reverse. The entire unit is
position
SEE MORE:
DTC P1157: A/F Sensor (Sensor 1) AFS Circuit
High Voltage
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information.
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, and wait 1 minute.
4. Check for Temporary DTCs or DTCs with the HDS.
Is DT
Transfer Assembly Inspection/Disassembly/Reassembly
Inspection
1. Set the dial indicator (A) on the companion flange
(B).
2. Measure the transfer gear backlash.
Standard: 0.06-0.16 mm (0.02-0.06 in.)
3. Secure the transfer housing (A) in a bench vise (B)
with soft jaws. To prevent damage to the transfer
housing, always use soft jaws or equivalent
m
© 2016-2025 Copyright www.hcrv.net
