Honda CR-V: Cylinder Head
Special Tools
- Air Pressure Regulator
- Valve Guide Reamer, 5.5 mm
- Socket, 19 mm
- Holder Handle
- Adjuster
- Locknut Wrench
- Stem Seal Driver
- VTEC Air Adapter
- VTEC Air Stopper
- Air Joint Adapter
- Crankshaft Pulley Holder
- Valve Guide Driver, 5.5 mm
- Attachment, 52 x 55 mm
- Driver
- Valve Spring Compressor Attachment
Component Location Index
-
IGNITION COIL COVER
-
CYLINDER HEAD COVER
-
CAM CHAIN
-
CAM CHAIN GUIDE B
-
CAM CHAIN GUIDE A
-
O-RING
-
VARIABLE VALVE TIMING CONTROL (VTC) OIL CONTROL
SOLENOID VALVE -
CRANKSHAFT PULLEY
-
CRANKSHAFT PULLEY BOLT
-
CHAIN CASE COVER
-
CHAIN CASE
-
CRANKSHAFT POSITION (CKP) SENSOR
-
AUTO-TENSIONER
-
TENSIONER ARM
-
CAM CHAIN GUIDE B
-
INTAKE CAMSHAFT
-
VTC ACTUATOR
-
EXHAUST CAMSHAFT SPROCKET
-
EXHAUST CAMSHAFT
-
DOWEL PINS
-
ROCKER ARM ASSEMBLY
-
CAMSHAFT HOLDERS
-
CMP PULSE PLATE B
-
CMP PULSE PLATE A
-
CMP SENSOR B (EXHAUST)
-
CMP SENSOR A (INTAKE)
-
CYLINDER HEAD BOLT
-
INTAKE VALVE SPRING
-
INTAKE VALVE SEAL
-
INTAKE VALVE GUIDE
-
INTAKE VALVE
-
CYLINDER HEAD GASKET
-
ROCKER ARM OIL CONTROL
SOLENOID FILTER -
ROCKER ARM OIL
CONTROL SOLENOID -
HEAT SHIELD
-
EXHAUST VALVE GUIDE
-
EXHAUST VALVE SPRING
-
VALVE COTTERS
-
SPRING RETAINER
-
EXHAUST VALVE SEAL
-
VALVE SPRING SEAT
- Engine Compression Inspection
- Valve Clearance Adjustment
- Cam Chain Removal
- Cam Chain Installation
- Auto-tensioner Removal and Installation
- Cam Chain Inspection
- CKP Pulse Plate Replacement
- Cylinder Head Cover Removal/Installation
- Cylinder Head Removal
- VTC Actuator, Exhaust Camshaft Sprocket Replacement
- Camshaft Inspection
- Valve, Spring, and Valve Seal Removal
- Valve, Spring, and Valve Seal Installation
- Cylinder Head Installation
READ NEXT:
Engine Compression Inspection
NOTE: After this inspection, you must reset the
powertrain control module (PCM), otherwise the PCM
will continue to stop the injectors from functioning.
Select PCM reset using the Honda Diagnostic Sy
Valve Clearance Adjustment
Special Tools Required
Adjuster 07MAA-PR70110
Locknut wrench 07MAA-PR70120
NOTE: Adjust the valves only when the cylinder head
temperature is less than 100 ºF (38 ºC).
1. Remove the cylinder hea
Cam Chain Removal
NOTE: Keep the cam chain away from magnetic fields.
1. Remove the front wheels.
2. Remove the splash shield (see step 21).
3. Remove the drive belt.
4. Remove the cylinder head cover.
5. Set the N
SEE MORE:
DTC 71-2x ("x" can be 0 thru 9 or A thru F):
Short in Driver's Seat Position Sensor
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures.
1. Erase the DTC memory.
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SRS indicator stay on, and is DTC 71-2x
indicated?
YES-G
Important Handling Information
Your CR-V has higher ground clearance than a passenger vehicle designed for
use only on pavement. Higher ground
clearance has many advantages for off-highway driving. It allows you to travel
over bumps, obstacles, and rough
terrain. It also provides good visibility so you can anticipate prob
