Honda CR-V: Cylinder Head
Special Tools
- Air Pressure Regulator
- Valve Guide Reamer, 5.5 mm
- Socket, 19 mm
- Holder Handle
- Adjuster
- Locknut Wrench
- Stem Seal Driver
- VTEC Air Adapter
- VTEC Air Stopper
- Air Joint Adapter
- Crankshaft Pulley Holder
- Valve Guide Driver, 5.5 mm
- Attachment, 52 x 55 mm
- Driver
- Valve Spring Compressor Attachment
Component Location Index
-
IGNITION COIL COVER
-
CYLINDER HEAD COVER
-
CAM CHAIN
-
CAM CHAIN GUIDE B
-
CAM CHAIN GUIDE A
-
O-RING
-
VARIABLE VALVE TIMING CONTROL (VTC) OIL CONTROL
SOLENOID VALVE -
CRANKSHAFT PULLEY
-
CRANKSHAFT PULLEY BOLT
-
CHAIN CASE COVER
-
CHAIN CASE
-
CRANKSHAFT POSITION (CKP) SENSOR
-
AUTO-TENSIONER
-
TENSIONER ARM
-
CAM CHAIN GUIDE B
-
INTAKE CAMSHAFT
-
VTC ACTUATOR
-
EXHAUST CAMSHAFT SPROCKET
-
EXHAUST CAMSHAFT
-
DOWEL PINS
-
ROCKER ARM ASSEMBLY
-
CAMSHAFT HOLDERS
-
CMP PULSE PLATE B
-
CMP PULSE PLATE A
-
CMP SENSOR B (EXHAUST)
-
CMP SENSOR A (INTAKE)
-
CYLINDER HEAD BOLT
-
INTAKE VALVE SPRING
-
INTAKE VALVE SEAL
-
INTAKE VALVE GUIDE
-
INTAKE VALVE
-
CYLINDER HEAD GASKET
-
ROCKER ARM OIL CONTROL
SOLENOID FILTER -
ROCKER ARM OIL
CONTROL SOLENOID -
HEAT SHIELD
-
EXHAUST VALVE GUIDE
-
EXHAUST VALVE SPRING
-
VALVE COTTERS
-
SPRING RETAINER
-
EXHAUST VALVE SEAL
-
VALVE SPRING SEAT
- Engine Compression Inspection
- Valve Clearance Adjustment
- Cam Chain Removal
- Cam Chain Installation
- Auto-tensioner Removal and Installation
- Cam Chain Inspection
- CKP Pulse Plate Replacement
- Cylinder Head Cover Removal/Installation
- Cylinder Head Removal
- VTC Actuator, Exhaust Camshaft Sprocket Replacement
- Camshaft Inspection
- Valve, Spring, and Valve Seal Removal
- Valve, Spring, and Valve Seal Installation
- Cylinder Head Installation
READ NEXT:
Engine Compression Inspection
NOTE: After this inspection, you must reset the
powertrain control module (PCM), otherwise the PCM
will continue to stop the injectors from functioning.
Select PCM reset using the Honda Diagnostic Sy
Valve Clearance Adjustment
Special Tools Required
Adjuster 07MAA-PR70110
Locknut wrench 07MAA-PR70120
NOTE: Adjust the valves only when the cylinder head
temperature is less than 100 ºF (38 ºC).
1. Remove the cylinder hea
Cam Chain Removal
NOTE: Keep the cam chain away from magnetic fields.
1. Remove the front wheels.
2. Remove the splash shield (see step 21).
3. Remove the drive belt.
4. Remove the cylinder head cover.
5. Set the N
SEE MORE:
To Stop Playing a Disc
Press the eject button (
) to
remove the disc. If you eject the disc,
but do not remove it from the slot,
the system will automatically reload
the disc after 10 seconds and put it in
pause mode. To begin playing, press
the CD/AUX button.
You can also eject the disc when the
igniti
System Diagnostic Mode
Start-up procedure and Diagnosis Menu
1. Turn the ignition switch to the ON (II) position.
Press and hold the Menu, the Map/Guide, and the
Cancel buttons. Keep them pressed for
approximately 3 seconds. The display screen then
goes directly to the Diagnostic Menu.
DIAGNOSTIC MENU SCREEN
2. After th
