Honda CR-V: DTC Troubleshooting
Honda CR-V (2006–2011) Service Manual / Restraints / SRS (Supplemental Restraint System) / DTC Troubleshooting
- DTC 11-1x/4x ("x" can be 0 thru 9 or A thru F) : Open or Increased Resistance in Driver's Airbag First/Second Inflator
- DTC 21-1x ("x" can be 0 thru 9 or A thru F): Open or Increased Resistance in Driver's Seat Belt Tensioner
- DTC 22-3x ("x" can be 0 thru 9 or A thru F): Short to Another Wire or Decreased Resistance in Front Passenger's Seat Belt Tensioner
- DTC 28-3x ("x" can be 0 thru 9 or A thru F): Short to Another Wire or Decreased Resistance in Front Passenger's Seat Belt Buckle Tensioner
- DTC 31-3x ("x" can be 0 thru 9 or A thru F): Short to Another Wire or Decreased Resistance in Driver's Side Airbag Inflator
- DTC 32-8x ("x" can be 0 thru 9 or A thru F): Short to Power in Front Passenger's Side Airbag Inflator
- DTC 33-9x ("x" can be 0 thru 9 or A thru F): Short to Ground in Left Side Curtain Airbag Inflator
- DTC 41-1x ("x" can be 0 thru 9 or A thru F): No Signal From the Left Front Impact Sensor
- DTC 45-1x ("x" can be 0 thru 9 or A thru F): No Signal From the Left Side Impact Sensor (second)
- DTC 71-2x ("x" can be 0 thru 9 or A thru F): Short in Driver's Seat Position Sensor
- DTC 82-14: No Signal From the Front Passenger's Weight Sensor (front inner side)
- DTC 83-26: No Signal From the Front Passenger's Weight Sensor (rear outer side)
READ NEXT:
DTC 11-1x/4x ("x" can be 0 thru 9 or A thru F) :
Open or Increased Resistance in Driver's
Airbag First/Second Inflator
DTC 11-1x ("x" can be 0 thru 9 or A thru F):
Open or Increased Resistance in Driver's
Airbag First Inflator
DTC 11-4x ("x" can be 0 thru 9 or A thru F):
Open or Increased Resistance in Driver's
Airbag
DTC 21-1x ("x" can be 0 thru 9 or A thru F):
Open or Increased Resistance in Driver's Seat
Belt Tensioner
DTC 21-1x ("x" can be 0 thru 9 or A thru F):
Open or Increased Resistance in Driver's Seat
Belt Tensioner
Special Tools Required
SRS inflator simulator 07SAZ-TB4011A
SRS simulator lead
DTC 22-3x ("x" can be 0 thru 9 or A thru F):
Short to Another Wire or Decreased
Resistance in Front Passenger's Seat Belt
Tensioner
Special Tools Required
SRS inflator simulator 07SAZ-TB4011A
SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures.
1. Erase th
SEE MORE:
Block and Piston Inspection
1. Remove the crankshaft and pistons.
2. Check the piston for distortion or cracks.
3. Measure the piston diameter at a point 13 mm
(0.5 in.) from the bottom of the skirt. There are two
standard-size pistons (No Letter or A, and B). The
letter is stamped on the top of the piston. Letters
are also
Front Driveshaft Installation
1. Apply grease to the contact area (A) of the outboard
joint and front wheel bearing.
NOTE: Failure to apply grease may cause excessive
noise and vibration.
2. Install a new set ring (A) onto the set ring groove
(B) of the driveshaft (left driveshaft).
3. Apply 0.5-1.0 g (0.02-0.04 oz) of grease
© 2016-2025 Copyright www.hcrv.net
