Honda CR-V: Symptom Troubleshooting

SRS indicator does not come on

1. Connect the HDS to the DLC.

2. Turn the ignition switch ON (II).

3. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate, troubleshoot the DLC circuit.

4. Check for PGM-FI, Body Electrical, and SRS DTCs with the HDS.

Are there any PGM-FI, Body Electrical, or SRS DTCs? YES-Go to the indicated DTCs troubleshooting.

NO-Go to step 5.

5. Do the gauge control module self-diagnostic function.

Does the SRS indicator come on? YES-Faulty SRS unit; replace the SRS unit.

NO-Faulty gauge control module; replace the gauge control module.

SRS indicator stays on, but no DTCs are stored

1. Connect the HDS to the DLC.

2. Turn the ignition switch ON (II).

3. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate, troubleshoot the DLC circuit.

4. Select Body Electrical status with the HDS.

5. Check for DTCs in the Gauge Menu with the HDS.

Is DTC B1187 indicated? YES-Go to the troubleshooting for DTC B1187.

NO-Go to step 6.

6. Check that the HDS communicates with the SRS unit.

Does the HDS communicates with the SRS unit? YES-Go to step 7.

NO-If the HDS does not communicate with the SRS unit, check for power and ground at the SRS unit connector A (28P). If power and grounds are still present, replace the SRS unit.

7. From the HDS System Menu, select SRS, then SRS in Mode Menu, PARAMETER INFORMATION, then SCS, MES, Indicator. Read the current status of the SRS indicator.

Is the status ON? YES-Faulty SRS unit; replace the SRS unit.

NO-Faulty gauge control module; replace the gauge control module.

Side airbag cutoff indicator stays on

1. Make sure nothing is on the front passenger's seat.

2. Make sure the seat-back is dry.

3. Turn the ignition switch ON (II), and see if the SRS indicator comes on.

Does the SRS indicator come on? YES-Go to the Symptom Troubleshooting "SRS indicator stays on, but no DTCs are stored".

NO-Go to step 2.

4. Connect the HDS to the DLC.

5. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not troubleshoot the DLC circuit.

6. From the Main Menu on the HDS, select SRS, then PARAMETER INFORMATION. In the PARAMETER INFORMATION Menu, select "scs, MES, Indicator," and read what is indicated on the HDS.

Is OFF indicated on the HDS? YES-Faulty gauge control module; replace the gauge control module.

NO-Faulty SRS unit; replace the SRS unit.

Side airbag cutoff indicator does not come on

NOTE: If the SRS indicator also stays on, go to SRS indicator stays on, but no DTCs are stored.

1. Turn the ignition switch ON (II), and check that the side airbag cutoff indicator comes on for about 6 seconds.

Does the side airbag cutoff indicator come on? YES-Go to the Symptom Troubleshooting "SRS indicator stay on." NO-Go to step 2.

2. Connect the HDS to the DLC.

3. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not troubleshoot the DLC circuit.

4. Do the self diagnostic function with the HDS.

Does the side airbag cutoff indicator come on? YES-Faulty SRS unit; replace the SRS unit.

NO-Faulty gauge control module; replace the gauge control module.

Passenger's airbag cutoff indicator stays on or comes on suddenly

NOTE: Under the following conditions, the passenger's airbag cutoff indicator stays on or comes on suddenly.

Does the passenger's airbag cutoff indicator stay on? YES-Go to step 2.

NO-Troubleshooting is complete.

2. Connect the HDS to the DLC.

3. Turn the ignition switch ON (II).

4. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate troubleshoot the DLC circuit.

5. Select the INSPECTION menu on the HDS, then select AFTER REPLACING FRONT PASSENGER'S SEAT COMPONENT(S), and follows the prompts.

Does the passenger's airbag cutoff indicator stay on? YES-Go to step 6.

NO-Troubleshooting is complete.

6. Select the INSPECTION menu on the HDS, then select AFTER A VEHICLE COLLISION, and follow the prompts.

Does the passenger's airbag cutoff indicator stay on? YES-Faulty SRS unit; replace the SRS unit.

NO-Troubleshooting is complete.

READ NEXT:

 Component Replacement/Inspection After Deployment

NOTE: Before doing any SRS repairs, use the HDS SRS menu method to check for DTCs; refer to the DTC Troubleshooting Index for the less obvious deployed parts (seat belt tensioners, front impact s

 Driver's Airbag Replacement

Removal 1. Disconnect the negative cable from the battery and wait at least 3 minutes before beginning work. 2. Remove the access panel (A) from the steering wheel, then disconnect the driver's airba

 Front Passenger's Airbag Replacement

Removal 1. Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work. 2. Remove the passenger's vent panel. 3. Remove the dashboard center upper panel. 4. Re

SEE MORE:

 Protecting Infants

Child Seat Type An infant must be properly restrained in a rear-facing, reclining child seat until the child reaches the seat maker’s weight or height limit for the seat, and the child is at least one year old. Only a rear-facing child seat provides proper support for a baby’s

 Fuel Pump Circuit Troubleshooting

If you suspect a problem with the fuel pump, check that the fuel pump actually runs; when it is on, you will hear some noise if you listen to the fuel fill port with the fuel f ill cap removed. The fuel pump should run for 2 seconds when the ignition switch is first turned on. If the fuel pump does

© 2016-2024 Copyright www.hcrv.net