Honda CR-V: Head Restraints

See page for important safety information and a warning about improperly positioning head restraints.

Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from the likelihood of whiplash and other injuries.

They are most effective when you

They are most effective when you adjust them so the center of the back of the occupant’s head rests against the center of the restraint.

Adjusting the Head Restraint

Adjusting the Head Restraint

The head restraints adjust for height.

You need both hands to adjust a restraint.Do not attempt to adjust it while driving. To raise it, pull upward.

To lower the restraint, push the release button sideways, and push the restraint down.

To pivot the outer head restraint

To pivot the outer head restraint down for better visibility, press the tilt button on the side of the head restraint. It folds down forward. To raise the head restraint, pivot it up by hand. Make sure the head restraint locks in position.

Removing the Head Restraint

Removing the Head Restraint

To remove a head restraint, pull it up as far as it will go. Push the release button, then pull the restraint out of the seat-back.

When a passenger is seated in the rear center seating position, make sure the center head restraint is properly adjusted.

Failure to reinstall the head

Failure to reinstall the head restraints can result in severe injury during a crash.

Always replace the head restraints before driving.

Make sure the removed head restraints are securely stored.

When reinstalling a head restraint, put the legs back in place. Then adjust it to the appropriate height while pressing the release button.

Make sure the head restraint locks in position when you reinstall it.

Active Head Restraints

The driver’s and front passenger’s

The driver’s and front passenger’s seats have active head restraints. If the vehicle is struck severely from the rear, the occupant properly secured with the seat belt will be pushed against the seat-back and the head restraint will automatically move forward.

This reduces the distance between the restraint and the occupant’s head.

It also helps protect the occupants against the likelihood of whiplash and injuries to the neck and upper spine.

After a collision, the activated restraint should return to its normal position.

If the restraints do not return to their normal position, or in the event of a severe collision, have the vehicle inspected by a Honda dealer.

For a head restraint system to work properly:

Do not hang any items on the head restraints, or from the restraint legs.

Do not place any object between an occupant and the seat-back.

Install each restraint in its proper location.

Only use genuine Honda replacement head restraints.

READ NEXT:

 Reclining the Front Seats

You can recline the seat-backs on the front seats so they are level with the rear seat cushions, making a large cushioned area. To do this: EX-L and Canadian EX models Only the passengerâ€

 Folding the Rear Seats Down

Each rear seat-back can be folded down separately to give more cargo room. With either of the outer seatbacks folded-down, you can still carry a passenger in the rear seat. With the center se

 Folding the Rear Seat Forward

The left and right rear seats can be folded up separately to make room for cargo. To fold the rear seat forward: Remove any items from the seat before you fold up the seat cushion. 1. Pul

SEE MORE:

 Driver's Airbag Replacement

Removal 1. Disconnect the negative cable from the battery and wait at least 3 minutes before beginning work. 2. Remove the access panel (A) from the steering wheel, then disconnect the driver's airbag 4P connector (B) and horn switch 1P connector (C) from the cable reel. 3. Using a TORX T30 bit, r

 Valve, Spring, and Valve Seal Removal

Special Tools Required Valve spring compressor attachment 07757-PJ1010A Identify the valves and valve springs as they are removed so that each item can be reinstalled in its original position. 1. Remove the cylinder head. 2. Using an appropriate-sized socket (A) and plastic mallet (B), lightly tap

© 2016-2024 Copyright www.hcrv.net