Honda CR-V: Headliner Removal/Installation
SRS components are located in this area. Review the SRS component locations
and the precautions and procedures before
doing repairs or service.
NOTE:
- Put on gloves to protect your hands.
- Use the appropriate tool from the KTC trim tool set to
avoid damage when prying components.
- Take care not to bend or scratch the trim and panels.
1. Make sure you have the anti-theft codes for the
audio and the navigation system, then write down
the XM audio presets (if equipped).
2. Disconnect the negative cable from the battery, and
a wait at least 3 minutes before beginning work.
3. Remove these items:
- A-pillar trim, both sides
- B-pillar upper trim, both sides
- Quarter pillar glass trim, both sides
- Ceiling light
- Sunvisors, both sides
- Grab handles, four places
4. Remove the roof console (A).
- Remove the lenses (B), and remove the bolts
(C).
- Open the console, and remove the bolts (D).
- Lower the roof console, and disconnect the
map light connector (E). If equipped,
disconnect the moonroof switch connector (F)
and navigation microphone connector (G).
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2708.jpg)
5. Remove the cap (A) from the center seat belt
retractor cover (B).
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2709.jpg)
6. Lower the headliner (A).
- Remove the front door opening seals (B), rear
door opening seals (C), and tailgate
weatherstrip (D) from each roof portion.
- Release the clips (E) and Velcro fasteners (F)
from the headliner by pulling down. Take care
not to damage the headliner.
- Lower the headliner carefully.
Without moonroof
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2710.jpg)
With moonroof
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2711.jpg)
7. Remove the cushion tapes, then remove the
interior wire harness (A) and antenna lead (AM/FM)
(B) from the headliner.
Without moonroof
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2712.jpg)
With moonroof
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2713.jpg)
8. With the help of an assistant, pull the headliner (A)
out through the tailgate opening. Do not bend the
liner. Bending the liner will crease and damage it.
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2714.jpg)
9. Remove the screws, and remove the retractor
cover bracket (A) and retractor cover (B) from the
headliner.
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2715.jpg)
10. If necessary, remove the side curtain airbag
mounting bolt (A) and grab handle bracket
mounting bolts (B), then remove the grab handle
bracket (C) from each side clips (D) by pulling the
bracket. Check if clips (Japan-produced model) are
damaged or stress-whitened, and if necessary,
replace them with new ones.
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2716.jpg)
11. Install the headliner in the reverse order of removal,
and note these items:
Headliner
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2717.jpg)
Grab handle
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2718.jpg)
Sunvisor
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2719.jpg)
Carpet Replacement
Special Tools Required
KTC trim tool set SOJATP2014 *
* Available through the American Honda Tool and
Equipment Program; call 888-424-6857
SRS components are located in this area. Review the
SRS component locations and the
precautions and procedures before
doing repairs or service.
NOTE:
- Put on gloves to protect your hands.
- Use the appropriate tool from the KTC trim tool set to
avoid damage when prying components.
- Take care not to damage, wrinkle, or twist the carpet.
- Be careful not to damage the dashboard or other
interior trim pieces.
1. Remove these items:
- Front seats, both sides
- Rear seat, both sides
- Front door sill trim, both sides (see step 1)
- Rear door sill trim, both sides (see step 2)
- Dashboard center lower cover (see step 3)
- Kick panels, both sides (see step 3)
- B-pillar lower trim (see step 3)
- Driver's dashboard undercover
- Passenger's dashboard undercover
- Center console
- Steering joint cover
2. Detach the clips, then remove the footrest (A).
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2720.jpg)
3. Remove the clips.
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2721.jpg)
4. Release the fasteners (A), then pull back the carpet
(B) from under the dashboard.
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2722.jpg)
5. Pull the seat harnesses (C) out through the hole in
the carpet, then remove the carpet.
6. From back of the front carpet: Release the hooks (A)
of the base (B) with a flat-tip screwdriver, and push
up the projections of the holder from the base to
remove the floor mat holder (C).
![Honda CR-V. Interior Trim](images/books/1602/honda_cr-v_headliner_removal_installation_2723.jpg)
7. Install the carpet in the reverse order of removal,
and note these items:
- Take care not to damage, wrinkle, or twist the
carpet.
- Make sure the seat harnesses and routed
correctly.
- Check if the clips are damaged or stress-whitened,
and if necessary, replace them with
new ones.
- Push the fasteners and clips into place securely.
READ NEXT:
Center Console Removal/Installation
Special Tools Required
KTC trim tool set SOJATP2014 *
* Available through the American Honda Tool and
Equipment Program; call 888-424-6857
SRS components are locate
Special Tools Required
KTC trim tool set SOJATP2014 *
* Available through the American Honda Tool and
Equipment Program; call 888-424-6857
NOTE:
Put on gloves to protect your hands.
Use the appropr
SEE MORE:
Component Location Index
ROCKER ARM OIL CONTROL VALVE
Removal/Installation
ROCKER ARM OIL PRESSURE SWITCH
Removal/Installation
CAMSHAFT POSITION (CMP) SENSOR A (INTAKE)
Replacement
POWERTRAIN CONTROL
MODULE (PCM)
Gene
After all occupants have adjusted
their seats and head restraints, and
put on their seat belts, it is very
important that they continue to sit
upright, well back in their seats, with
their feet on the floor, until the
vehicle is safely parked and the
engine is off.
Sitting improperly
© 2016-2024 Copyright www.hcrv.net
![](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAEALAAAAAABAAEAAAIBTAA7)