Honda CR-V: DTC P0752: Shift Solenoid Valve A Stuck ON

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review General Troubleshooting Information.

1. Warm up the engine to normal operating temperature (the radiator fan comes on).

2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.

3. Drain the ATF (see step 3 on page 14-239) through a strainer. Inspect the strainer for metal debris or excessive clutch material.

Does the strainer have metal debris or excessive clutch material? YES-Replace the transmission, then go to step 13.

NO-Replace the ATF (see step 5 on page 14-239), then go to step 4.

4. Clear the DTC with the HDS.

5. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

6. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

7. Monitor the OBD STATUS for P0752 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate FA/LED? YES-Go to step 8.

NO-Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return to step 5 and recheck.

8. Clear the DTC with the HDS.

9. Choose Shift Solenoid A in the Miscellaneous Test Menu, and make sure the shift solenoid valve A operates with the HDS.

Is a clicking sound heard? YES-Go to step 10.

NO-Replace shift solenoid valve A , then go to step 13.

10. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

11. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

12. Monitor the OBD STATUS for P0752 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate FAILED? YES-Repair shift valve A, or replace the transmission, then go to step 13.

NO-Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return to step 10 and recheck.

13. Clear the DTC with the HDS.

14. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

15. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

16. Monitor the OBD STATUS for P0752 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate PASSED? YES-Troubleshooting is complete.

NO-If the HDS indicates FAILED, return to step 1 and recheck. If the HDS indicates NOT COMPLETED, return to step 14 and recheck.

DTC P0756: Shift Solenoid Valve B Stuck OFF

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review General Troubleshooting Information.

1. Warm up the engine to normal operating temperature (the radiator fan comes on).

2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.

3. Drain the ATF (see step 3 on page 14-239) through a strainer. Inspect the strainer for metal debris or excessive clutch material.

Does the strainer have metal debris or excessive clutch material? YES-Replace the transmission, then go to step 13.

NO-Replace the ATF (see step 5 on page 14-239), then go to step 4.

4. Clear the DTC with the HDS.

5. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

6. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

7. Monitor the OBD STATUS for P0756 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate FAILED? YES-Go to step 8.

NO-Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return to step 5 and recheck.

8. Clear the DTC with the HDS.

9. Choose Shift Solenoid B in the Miscellaneous Test Menu, and make sure the shift solenoid valve B operates with the HDS.

Is a clicking sound heard? YES-Go to step 10.

NO-Replace shift solenoid valve B , then go to step 13.

9. Choose Shift Solenoid B in the Miscellaneous Test Menu, and make sure the shift solenoid valve B operates with the HDS.

Is a clicking sound heard? YES-Go to step 10.

NO-Replace shift solenoid valve B, then go to step 13.

13. Clear the DTC with the HDS.

14. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

15. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

16. Monitor the OBD STATUS for P0756 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate PASSED? YES-Troubleshooting is complete.

NO-If the HDS indicates FAILED, return to step 1 and recheck. If the HDS indicates NOT COMPLETED, return to step 14 and recheck.

DTC P0757: Shift Solenoid Valve B Stuck ON

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review General Troubleshooting Information.

1. Warm up the engine to normal operating temperature (the radiator fan comes on).

2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.

3. Drain the ATF (see step 3 on page 14-239) through a strainer. Inspect the strainer for metal debris or excessive clutch material.

Does the strainer have metal debris or excessive clutch material? YES-Replace the transmission, then go to step 13.

NO-Replace the ATF (see step 5 on page 14-239), then go to step 4.

4. Clear the DTC with the HDS.

5. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

6. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

7. Monitor the OBD STATUS for P0757 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate FAILED? YES-Go to step 8.

NO-Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return to step 5 and recheck.

8. Clear the DTC with the HDS.

9. Choose Shift Solenoid B in the Miscellaneous Test Menu, and make sure the shift solenoid valve B operates with the HDS.

Is a clicking sound heard? YES-Go to step 10.

NO-Replace shift solenoid valve B , then go to step 13.

10. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

11. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

12. Monitor the OBD STATUS for P0757 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate FAILED? YES-Repair shift valve B, or replace the transmission, then go to step 13.

NO-Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return to step 10 and recheck.

13. Clear the DTC with the HDS.

14. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

15. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

16. Monitor the OBD STATUS for P0757 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate PASSED? YES-Troubleshooting is complete.

NO-If the HDS indicates FAILED, return to step 1 and recheck. If the HDS indicates NOT COMPLETED, return to step 14 and recheck.

DTC P0761: Shift Solenoid Valve C Stuck OFF

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review General Troubleshooting Information.

1. Warm up the engine to normal operating temperature (the radiator fan comes on).

2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.

3. Drain the ATF (see step 3 on page 14-239) through a strainer. Inspect the strainer for metal debris or excessive clutch material.

Does the strainer have metal debris or excessive clutch material? YES-Replace the transmission, then go to step 13.

NO-Replace the ATF (see step 5 on page 14-239), then go to step 4.

4. Clear the DTC with the HDS.

5. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

6. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/ h) for more than 20 seconds, then slow down to a stop.

7. Monitor the OBD STATUS for P0761 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate FAILED? YES-Go to step 8.

NO-Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return to step 5 and recheck.

8. Clear the DTC with the HDS.

9. Choose Shift Solenoid C in the Miscellaneous Test Menu, and make sure the shift solenoid valve C operates with the HDS.

Is a clicking sound heard? YES-Go to step 10.

NO-Replace shift solenoid valve C, then go to step 13.

10. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

11. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

12. Monitor the OBD STATUS for P0761 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate FAILED? YES-Repair shift valve C, or replace the transmission, then go to step 13.

NO-Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return to step 10 and recheck.

13. Clear the DTC with the HDS.

14. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

15. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

16. Monitor the OBD STATUS for P0761 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate PASSED? YES-Troubleshooting is complete.

NO-If the HDS indicates FAILED, return to step 1 and recheck. If the HDS indicates NOT COMPLETED, return to step 14 and recheck.

DTC P0771: Shift Solenoid Valve E Stuck OFF

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review General Troubleshooting Information.

1. Warm up the engine to normal operating temperature (the radiator fan comes on).

2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.

3. Drain the ATF (see step 3 on page 14-239) through a strainer. Inspect the strainer for metal debris or excessive clutch material.

Does the strainer have metal debris or excessive clutch material? YES-Replace the transmission, then go to step 13.

NO-Replace the ATF (see step 5 on page 14-239), then go to step 4.

4. Clear the DTC with the HDS.

5. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

6. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

7. Monitor the OBD STATUS for P0771 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate FAILED? YES-Go to step 8.

NO-Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return to step 5 and recheck.

8. Clear the DTC with the HDS.

9. Choose Shift Solenoid E in the Miscellaneous Test Menu, and make sure the shift solenoid valve E operates with the HDS.

Is a clicking sound heard? YES-Go to step 10.

NO-Replace shift solenoid valve E , then go to step 13.

10. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

11. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

12. Monitor the OBD STATUS for P0771 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate FAILED? YES-Repair shift valve E, or replace the transmission, then go to step 13.

NO-Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return to step 10 and recheck.

13. Clear the DTC with the HDS.

14. Test-drive the vehicle in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

15. Test-drive the vehicle again in the D position through all five gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.

16. Monitor the OBD STATUS for P0771 in the DTCs/ Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate PASSED? YES-Troubleshooting is complete.

NO-If the HDS indicates FAILED, return to step 1 and recheck. If the HDS indicates NOT COMPLETED, return to step 14 and recheck.

READ NEXT: