Honda CR-V: MICU Input Test
NOTE:
- The MICU turns on the headlights (high beams) in a dim mode for the
daytime running lights under the following
conditions:
- The ignition switch is ON (II)
- The headlight switch is OFF
- The parking brake is released (parking brake switch OFF)
- If the vehicle is equipped with an optional remote control engine start system (Canada), the daytime running lights will not function when started with the remote start.
1. Before testing, troubleshoot the B-CAN System Diagnosis Test Mode A.
2. Check the No. 12 (10 A), No. 13 (10 A), No. 15 (7.5 A), No. 16 (10 A), No. 17 (10 A), No. 18 (20 A), No. 19 (15 A), No. 21 (30 A), and No. 37 (7.5 A) fuses in the under-dash fuse/relay box. If any fuse is blown, replace it and go to step 3.
3. Disconnect the under-dash fuse/relay box connectors E, F, G, M, S, and T.
NOTE: All connector views are wire side of female terminals.
4. Inspect the connector and socket terminals to be sure they are all making good contact.
- If the terminals are bent, loose or corroded, repair them as necessary and recheck the system.
- If the terminals look OK, go to step 5.
5. With the connectors still disconnected, make these input tests at the appropriate connector.
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If all the input tests prove OK, go to step 6.
6. Reconnect the connectors, and do these input tests at the connectors.
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If all the input tests prove OK, the MICU is faulty; replace the under-dash fuse/relay box.
Combination Light Switch Test/Replacement
1. Remove the dashboard lower cover.
2. Remove the steering column covers.
3. Disconnect the 12P connector (A) from the combination light switch (B).
4. Remove the two screws, then slide out the combination light switch.
5. Inspect the connector terminals to be sure they are all making good contact.
- If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
- If the terminals look OK, check for continuity between the terminals in each switch position according to the tables.
Light switch
Turn signal switch
6. If the continuity is not as specified, replace the switch.
READ NEXT:
Headlight Adjustment
CAUTION
Headlights become very hot during use; do not
touch them or any attaching hardware immediately
after they have been turned off.
Before adjusting the headlights:
Park the vehicle on a level s
Turn Signal/Hazard Flasher
Component Location Index
TURN SIGNAL SWITCH
(Built into the combination light switch)
TURN SIGNAL INDICATORS
HAZARD WARNING SWITCH
MICU (Built into the under-dash fuse/relay box)
Circuit Diagr
Interior Lights
Component Location Index
With moon roof
INDIVIDUAL MAP LIGHTS
INTERIOR LIGHT SWITCH
(Built into the moonroof switch)
AMBIENT LIGHT
(Built into the moonroof switch)
CEILING LIGHT
CARGO AREA LI
SEE MORE:
No sound is heard from speaker(s) (display is
normal) (with navigation)
NOTE:
Set the fader and balance positions to the center.
Before doing symptom troubleshooting, do the
power switch will not turn ON troubleshooting.
1. Check that the volume button is not set to the MIN
level.
Is it at MIN level? YES-Raise the volume level, and recheck the function.
NO-Go to
Introduction
Congratulations! Your selection of a 2010 Honda CR-V was a wise
investment. It will give you years of driving pleasure.
One of the best ways to enhance the enjoyment of your new vehicle is to
read this manual. In it, you will learn how to operate its driving controls and
convenience items. Af
