Honda CR-V: Cylinder Head Cover Removal/Installation
Cylinder Head Cover Removal
1. Remove the intake manifold cover.
2. Remove the four ignition coils.
3. Disconnect the evaporative emission (EVAP) canister purge valve connector.
4. Remove the dipstick (A), the breather hose (B), and power steering (P/S) hose clamp (C).
5. Remove two bolts (D) securing the EVAP canister purge valve bracket.
6. Remove the cylinder head cover.
Cylinder Head Cover Installation
1. Thoroughly clean the head cover gasket and the groove.
2. Install the head cover gasket (A) in the groove of the cylinder head cover (B).
3. Check that the mating surfaces are clean and dry.
4. Apply liquid gasket, P/N 08717-0004,08718-0001, 08718-0003, or 08718-0009, on the chain case and the No. 5 rocker shaft holder mating areas. Install the component within 5 minutes of applying the liquid gasket.
NOTE:
- If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
- If too much time has passed after applying the liquid gasket, remove the old liquid gasket and residue, then reapply new liquid gasket.
5. Set the spark plug seals (A) on the spark plug tubes.
Place the cylinder head cover (B) on the cylinder head, then slide the cover slightly back and forth to seat the head cover gasket.
6. Inspect the cover washers (C). Replace any washer that is damaged or deteriorated.
7. Tighten the bolts in two or three steps. In the final step tighten all bolts, in sequence, to 12 N*m (1.2 kgf*m, 8.7 Ibf*ft).
NOTE:
- Wait at least 30 minutes before filling the engine with oil.
- Do not run the engine for at least 3 hours after installing the head cover.
8. Install two bolts (A) securing the evaporative emission (EVAP) canister purge valve bracket.
9. Install the power steering (P/S) hose clamp (B), breather hose (C), and the dipstick (D).
10. Connect the EVAP canister purge valve connector.
11. Install the four ignition coils.
12. Install the intake manifold cover.
READ NEXT:
Cylinder Head Removal
NOTE:
Use fender covers to avoid damaging painted
surfaces.
To avoid damage, unplug the wiring connectors
carefully while holding the connector portion.
To avoid damaging the cylinder head, wait
VTC Actuator, Exhaust Camshaft Sprocket
Replacement
Removal
1. Remove the cam chain.
2. Hold the camshaft with an open-end wrench, then
loosen the variable valve timing control (VTC)
actuator mounting bolt and exhaust camshaft
sprocket mounting bolt.
Camshaft Inspection
NOTE: Do not rotate the camshaft during inspection.
1. Remove the rocker arm assembly.
2. Put the rocker shaft holders, camshaft, and
camshaft holders on the cylinder head, then tighten
the bolts, i
SEE MORE:
VSA (Vehicle Stability Assist) System Components
Component Location Index
VSA MODULATOR-CONTROL UNIT
Removal and Installation
UNDER-HOOD FUSE/RELAY BOX
DATA LINK
CONNECTOR (DLC)
STEERING ANGLE SENSOR
Replacement
VSA OFF SWITCH
Test
RIGHT-REAR WHEEL SENSOR
Replacement
HUB BEARING UNIT
(MAGNETIC ENCODER)
Replace
Evaporator Core
Replacement
1. Recover the refrigerant with a recovery/recycling/ charging station.
2. Remove the bolt from the A/C line clamp, and
remove the receiver line (A) from the clips (B).
3. Remove the nut, then disconnect the A/C lines (A)
from the evaporator core.
4. Remove the stud bolt.
5. Remove the blower un
