Honda CR-V: Sleep and Wake-up Mode Test
1. Shift to the sleep mode:
Turn the ignition switch OFF, and remove the key. If the MICU receives no
signals from the inputs listed below, it
will go into sleep mode in less than 40 seconds.
- Driver's door lock switch (LOCK or UNLOCK)
- Driver's door key cylinder switch (LOCK or UNLOCK)
- Front passenger's door lock switch (LOCK or UNLOCK)
- Tailgate latch switch (tailgate closed)
- Tailgate outer handle switch
- Hazard warning switch (OFF)
2. Confirm the sleep mode:
Check for voltage on the B-CAN communication line; there should be battery
voltage in the sleep mode. Check the
parasitic draw at the battery while shifting into the sleep mode; amperage
should change from about 200 mA to
less than 35 mA.
3. Shift to the wake up mode:
When the ignition switch is turned ON (II), the MICU, gauge control module,
immobilizer-keyless control unit-receiver,
and PCM wake up at the same time without "talking" to each other through the
communication lines.
When any switch in the multiplex integrated control system is turned on, it
wakes up its related control unit which,
in turn, wakes up the other units. After confirming the sleep mode, look in the
following table for the switch most
related to the problem. Operate that switch and see if its control unit wakes
up.
NOTE: If any control unit is faulty and will not wake up, several circuits in
the system will malfunction at the same
time. The MICU is followed by a list of the switches and input signals that can
wake it up.
- Door switches (door open)
- Driver's door lock switch (LOCK or UNLOCK)
- Driver's door lock knob switch (LOCK or UNLOCK)
- Driver's door key cylinder switch (LOCK or UNLOCK)
- Front passenger's door lock switch (LOCK or UNLOCK)
- Front passenger's door lock knob switch (UNLOCK)
- Left rear door lock knob switch
- Right rear door lock knob switch
- Tailgate latch switch (tailgate open)
- Tailgate outer handle switch
- Hood switch (with security) (hood open)
- Hazard warning switch (ON)
- Combination light switch (parking, headlight, dimmer, passing ON)
- Ignition key switch (key inserted)
Circuit Diagram

READ NEXT:
DTC B1000: Communication Bus Line Error
(Bus-off)
1. Clear the DTCs with the HDS.
2. Turn the ignition switch OFF, and then back ON (II).
3. Wait for 6 seconds or more.
4. Check for DTCs with the H
NOTE: Before testing, troubleshoot the B-CAN System Diagnosis Test Mode A.
1. Turn the ignition switch OFF.
2. Disconnect the under-dash fuse/relay box connectors E, F, G, K, R, and T.
NOTE: All con
Component Location Index
NAVIGATION UNIT or
AUDIO UNIT
IMMOBILIZER-KEYLESS
CONTROL UNIT
(Built-in receiver)
MICU (Built into the under-dash fuse/relay box)
HEADLIGHTS
HORN
HOOD SWITCH
SECUR
SEE MORE:
Do not attempt to deactivate your
airbags. Together, airbags and
seat belts provide the best
protection.
Do not tamper with airbag
components or wiring for any
reason. Tampering could cause
the airbags to deploy, possibly
causing very serious injury.
Do not expose the front passenger
Mainshaft Bearing and Oil Seal
Replacement
Special Tools Required
Adjustable bearing puller, 25-40 mm
07736-A01000B or 07736-A01000A
Attachment, 62 x 68 mm 07746-0010500
Attachment, 72 x 75 mm 07746-0010600
Driver 07749-0010000
1. Remove the mainshaft bearing and oil seal using
the adjustabl
© 2016-2025 Copyright www.hcrv.net
